FAQ – Questions & AnswersCategory: AR-15 FAQHow to remove AR-15 A2 stock?
Troy Harris asked 2 years ago
How to remove AR-15 A2 stock?

4 Answers
Olson answered 2 years ago

Removing an AR-15 A2 stock can be a bit tricky, but with the right tools and a little bit of know-how, it’s not too difficult.

Here’s what you’ll need to do:

1. First, make sure that your AR-15 is unloaded. Once you have verified that there are no rounds in the chamber or magazine, proceed to the next step.

2. Locate the two screws that secure the A2 stock to the lower receiver. These screws are typically located at the rear of the receiver, near where the stock meets the receiver extension (the tube that runs from the back of the lower receiver to the buttstock).

3. Using a correctly sized Allen wrench, remove the two screws from the lower receiver.

4. Once the screws have been removed, the A2 stock can now be slid off of the receiver extension.

5. To install a new stock, simply reverse the above steps. Make sure to torque the screws to the correct specification, and you’re good to go!

Lewis answered 2 years ago
If you’re looking to remove the A2 stock from your AR-15, there are a few things you’ll need to know. First, it’s important to understand that the A2 stock is a fixed position stock, meaning it cannot be adjusted. This makes it a great choice for those who want a more stable shooting platform, but can be more difficult to use for those who are not as comfortable with firearms.
To remove the A2 stock, you will first need to disengage the locking mechanism. This is located on the left side of the receiver, just above the magazine release button. Once you have disengaged the locking mechanism, you will be able to slide the stock off of the receiver.
 
How to remove AR-15 A2 stock?
 
You may also need to remove the buffer tube assembly to completely remove the A2 stock. This is not always necessary, but if you are having difficulty removing the stock, this may be the issue. To remove the buffer tube assembly, simply unscrew it from the receiver.
With the A2 stock removed, you will now be able to install the stock of your choice. There are a variety of aftermarket stocks available, so be sure to do your research to find the one that best suits your needs. Thanks for reading!

Ivan answered 2 years ago

Here’s how to remove an AR-15 A2 stock. Start by making sure the gun is unloaded. Then, locate the release button on the back of the stock. Press it in and hold it while you pull the stock off the gun. If you’re having trouble, try wiggling the stock a bit as you pull it off.

Once the stock is off, you’ll be able to access the recoil spring and buffer assembly. Carefully remove these parts from the gun. Be careful not to lose any small springs or detent pins. With these parts removed, you should now be able to simply slide the old stock out of its housing on the back of the receiver.

To install the new stock, start by sliding it into the housing on the back of the receiver. Then, replace the buffer assembly and recoil spring. Make sure these parts are properly seated before continuing. Once they’re in place, you can put the stock back on the gun. Start by lining up the release button on the back of the stock with the hole in the receiver. Then, press the stock into place until it clicks. Your new stock is now installed!

We also recommend that you watch this video

Jordan answered 2 years ago
If you’re looking to remove your AR-15 A2 stock, there are a few things you’ll need to know first. The process is fairly simple, but it’s always best to consult with a professional before making any changes to your firearm.
1. First, you’ll need to remove the rear takedown pin by pressing in on the retaining latch and sliding the pin out.
2. Next, you’ll need to remove the stock by pulling it straight back.
Be careful not to lose the buffer spring or detent when removing the stock.
Once the stock is off, you can install a new stock of your choice. Many shooters prefer an adjustable stock, as it allows for a more customized fit.