How to lubricate an AR15?

If you’re looking to lubricate your AR-15, there are a few things you’ll need to take into account:

1. First and foremost, you’ll need to make sure that you choose the right type of lubricant. You don’t want to use anything too thick or oily, as this can potentially gum up your weapon and cause problems down the line. A light firearm-specific oil is usually the best bet.

2. Next, you’ll need to figure out how much lubricant to use. Again, err on the side of caution here – you don’t want to use too much. A little bit goes a long way when it comes to firearms, so start with a small amount and build up from there if needed.

3. Finally, you’ll need to decide where to apply the lubricant. It’s important to hit all of the key areas, such as the bolt carrier group, trigger assembly, and any moving parts. A good rule of thumb is to apply the lubricant to any area where two metal surfaces are in contact with each other.

With all of that in mind, let’s take a look at how to lubricate an AR15 step-by-step.

Step 1: Gather Your Materials

First things first, you’ll need to gather your materials. In addition to your chosen lubricant, you’ll also need some rags or cleaning cloths. These will come in handy for wiping away any excess lubricant.

Step 2: Apply the Lubricant to Moving Parts

Now it’s time to start applying the lubricant. As we mentioned before, you’ll want to focus on any area where two metal surfaces are in contact with each other. This includes the bolt carrier group, trigger assembly, and any other moving parts.
To apply the lubricant, simply put a few drops on your rag and then wipe it onto the desired area. Be sure to use a light touch – you don’t want to saturate the area with lubricant. A little bit should go a long way.

Step 3: Wipe Away Excess Lubricant

Once you’ve applied the lubricant to all of the moving parts, it’s time to wipe away any excess. Again, you’ll want to use a clean rag or cloth for this. Simply wipe away any excess lubricant until the area is clean.

Step 4: Repeat as Needed

Depending on how often you use your AR15, you may need to lubricate it regularly. If you notice that the lubricant is starting to wear away or if your weapon starts to feel gummed up, simply repeat the process.

And that’s all there is to it! Lubricating your AR15 is a fairly simple process, but it’s important to do it right. By following the steps above, you can ensure that your weapon will stay in good condition and function properly for many years to come.

The AR15 is a gas-operated, semi-automatic rifle that is chambered for the 5.56x45mm NATO cartridge. It is a derivative of the M16 assault rifle, which is itself a descendant of the ArmaLite AR-15 rifle that was designed by Eugene Stoner in the 1950s. The AR15 is one of the most popular firearms in America, and it is used by hunters, shooters, and collectors alike.

Lubricating an AR15 is a simple process, but it must be done correctly to ensure the proper functioning of the firearm. Three main areas must be lubricated on an AR15:

• the bolt carrier group,
• the trigger assembly,
• the gas system.

The bolt carrier group is the heart of an AR15, and it must be properly lubricated to ensure that the firearm will function correctly. The best way to lubricate the bolt carrier group is to use a high-quality synthetic oil such as CLP or Break Free. Apply a small amount of oil to the charging handle and bolt carrier, and then use a clean rag to wipe off any excess oil.

The trigger assembly is another critical component of the AR15, and it must be lubricated to ensure smooth operation. Apply a small amount of oil to the trigger assembly, and then use a clean rag to wipe off any excess oil.

The gas system is the final area that must be lubricated on an AR15. Apply a small amount of oil to the gas tube and gas key, and then use a clean rag to wipe off any excess oil.

With these three areas properly lubricated, your AR15 will be ready to function properly. Remember to always clean and inspect your AR15 before lubricating it, and to always use a high-quality synthetic oil to ensure proper functioning.

We also recommend watching this video

It is important to keep your AR15 well lubricated to maintain its function and longevity. Fortunately, this process is relatively simple and only requires a few basic supplies.
Here is a step-by-step guide to properly lubricating your AR15:
1) Start by removing the dust cover from the upper receiver. Then, using a mild solvent, clean any dirt or debris from the inside of the receiver.
2) Next, apply a small amount of oil to a clean rag and wipe down the bolt carrier assembly. Be sure to get all of the moving parts, including the charging handle and bolt release.
3) With the bolt carrier assembly still removed, apply a light coat of oil to the inside of the upper receiver.
4) Finally, reassemble the bolt carrier assembly and replace the dust cover.
It is important to note that you should not over-lubricate your AR15. Too much oil can attract dirt and debris, which can cause problems down the road. A light coat of oil is all that is necessary to keep your AR15 in good working order.
 

AR15s require a little more care than your average gun when it comes to lubrication.
1. The first step is to identify the different parts of your AR15 that need lubrication. These include the bolt carrier group, the charging handle, and any moving parts on the rail system.
2. Once you know where to lube, the next step is to choose the right type of lubricant. A light oil or grease works best for an AR15. You don’t want to use too much lubricant as this can cause the collection of dirt and grime, which can eventually lead to problems with function. A good rule of thumb is to apply enough lubricant so that you can still see some metal shining though – you don’t want it to be completely covered.

To lubricate an AR15, you’ll need to start by field stripping the rifle. This means removing the upper and lower receivers, as well as the bolt carrier group.

Once you have everything disassembled, you’ll want to wipe down all of the parts with a clean cloth. Pay special attention to the gas key, bolt carrier, and charging handle. These are all important parts of the firearm that need to be properly lubricated.

Next, apply a light coat of oil or lubricant to all of the moving parts. Make sure that you don’t over-lubricate, as this can cause problems down the line.

Once everything is lightly coated, reassemble the rifle and you’re good to go!